Product ID:BRUSHABLE CERAMIC RESIN
MSDS Date:12/14/1989
FSC:8040
NIIN:00N017842
Kit Part:Y
MSDS Number: BKZKT

ITW DEVCON CORPORATION

30 ENDICOTT STREET
DANVERS, MA 01923

Emergency Phone: 508-777-1100

Info Phone: 508-777-1100

Cage: 16509

ITW DEVCON CORPORATIO

DANVERS, MA 01923 US

Telephone: 508-777-1100

Cage: 16509

BISPHENOL A DIGLYCIDYL ETHER RESIN (DGEBA) LD50 (ORAL,RAT)

CAS: 25068-38-6

RTECS: SL6475000

Fraction By Weight: 40-60%

1,4-BIS (GLYCIDYOXYMETHYL) CYCLOHEXANE;

CAS: 14228-73-0

Fraction By Weight: 1-5%

LD50 LC50 Mixture:SEE INGREDIENTS.
Routes of Entry: Inhalation:NO Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:EYES: MILD IRRIT. SKIN: MAY CAUSE MILD
IRRIT. INHAL: UNLIKELY BECAUSE OF LOW VAP PRESS. NO DATA WERE FOUND
ON SPECIFIC SYMP. INGEST: ACUTE ORAL TOXICITY IS LOW. NO DATA WERE
FOUND ON SPECIFIC SYMP. EF TS OF CHRONIC OVEREXPOS: IN SMALL
FRACTION OF POPULATION (AROUND 1%) TOO MUCH SKIN CONTACT W/ (SEE
EFTS OF OVEREXPOS)
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:HLTH HAZ: EPOXY RESINS WILL CAUSE SENSIT.
ITCHING, SWELLING, OR RASHES MAY THEN RESULT FROM FURTHER CONTACT.
Medical Cond Aggravated by Exposure:ALLERGIES, ECZEMA, AND OTHER SKIN
DISORDERS.

First Aid:EYES: FLUSH EYE WITH CLEAN H*2O FOR AT LEAST 15 MIN WHILE
GENTLY HOLDING EYELIDS OPEN. GET MED ATTN. SKIN: WASH THORO W/SOAP
& H*2O. CONSULT PHYS IF IRRIT DEVELOPS. INHALATION: REMOVE PATIENT
TO FRESH AIR. ADMINISTER OXYGEN IF BRTHG IS DFCLT. GET MED ATTN IF
SYMPTOMS PERSIST. INGESTION: DO NOT INDUCE VOMITING. GIVE TWO
GLASSES OF WATER TO DILUTE. GET MEDICAL ATTENTION.

Flash Point Method:PMCC
Flash Point:>400F,204C
Extinguishing Media:CO*2, DRY CHEMICAL, FOAM.
Fire Fighting Procedures:FIREFIGHTERS SHOULD WEAR NIOSH/MSHA APPROVED
SCBA AND FULL PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:NONE SPECIFIED BY MANUFACTURER.

Spill Release Procedures:WEAR APPROPRIATE PROTECTIVE EQUIPMENT. ABSORB
SPILL ON INERT MATERIAL SUCH AS VERMICULITE OR SAND; SCRAPE UP AND
TRANSFER TO IMPERMEABLE CONTAINERS. WASH SPILL AREA WITH STRONG
DETERGENT AND WATER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:STORE WELL-CLOSED IN COOL, DRY PLACE.
HANDLE I/A/W POTENTIAL HAZ OF CURING AGENT. REMOVE CONTAM CLTHG AND
PROT GEAR; CLEAN THORO BEFORE USING AGAIN.
Other Precautions:IF MATL IS SANDED/MACHINED AFTER CURING, TAKE APPROP
PREC AGAINST INHAL OF NUISANCE PARTICULATES OF ALUMINUM OXIDE, A
SARA 313 LISTED TOXIC CHEM, & IRON (III) OXIDE, A SUSPECTED HUMAND
CARCINOGEN. TLV OF 10 MG/M3 SHOULD BE OBSERVED.

Respiratory Protection:NONE REQUIRED AT NORMAL HANDLING TEMPERATURES.
WEAR NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE FOR EXPOSURE OF
CONCERN .
Ventilation:LOCAL EXHAUST IS RECOMMENDED FOR CONFINED AREAS. GENERAL
MECHANICAL VENTILATION IS ADEQUATE FOR NORMAL USE.
Protective Gloves:CHEMICAL RESISTANT RUBBER GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:PROTECTIVE GEAR AS REQUIRED TO PREVENT SKIN
CONTACT.
Work Hygienic Practices:REMOVE CONTAM CLTHG & PROT GEAR; CLEAN THORO
BEFORE USING AGAIN.CONTAM LEATHER ARTICLES (INCLUDING SHOES)(SEE
SUPP DATA)
Supplemental Safety and Health
TOXIC CHEMICAL, AND IRON (III) OXIDE, A SUSPECTED HUMAN CARCINOGEN. A
TLV OF 10 MG/M3 SHOULD BE OBSERVED. HYGENIC PRACT: CANNOT BE
DECONTAMINATED & SHOULD BE DISCARDED.

HCC:N1
Vapor Pres:NIL @ 70 F
Vapor Density:>1
Spec Gravity:1.83
pH:7.0
Evaporation Rate & Reference:<1
Solubility in Water:NIL
Appearance and Odor:THICK, RED LIQUID WITH LITTLE ODOR.
Percent Volatiles by Volume:100

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS AND STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:EXTREME HEAT AND OPEN FLAME.
Hazardous Decomposition Products:OXIDES OF CARBON; ALDEHYDES AND ACIDS
FROM INCOMPLETE COMBUSTION.
Conditions to Avoid Polymerization:HEAT IS RELEASED WHEN THIS RESIN IS
MIXED WITH EPOXY HARDENERS; USE CATION WHEN MIXING LARGE
QUANTITIES.

Waste Disposal Methods:AFTER PROPER MIXING WITH HARDENER, PRODUCT FORMS
A NONHAZARDOUS SOLID-SEE DIRECTIONS FOR MIXING. UNMIXED WASTE RESIN
SHOULD BE DISCARDED IN ACCORDANCE WITH FEDERAL, STATE, AND LOCAL
REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.